How to install metal roof panel? - Printable Version +- ask aluminium Forum (https://www.askaluminium.com) +-- Forum: My Category (https://www.askaluminium.com/Forum-My-Category) +--- Forum: Knowledge & Technique (https://www.askaluminium.com/Forum-Knowledge-Technique) +--- Thread: How to install metal roof panel? (/Thread-How-to-install-metal-roof-panel)

How to install metal roof panel? - toyota1515 - 03-06-2018 Before installing the metal roof panel, check the specification model, geometric dimension, appearance, length and quantity of the metal roof board in the entrance, and check the layout plan of the metal roof. When the metal roof panel is installed, the position of the first metal roof panel shall be determined according to the plate-plate diagram. Generally, it starts from the direction of the prevailing wind direction. When the light plate is connected, the two butyl duct tape is finished, and the adhesive tape is filled with glass glue. The metal roof panel and the mining plate are connected, and the two sides of the mining plate are removed. And insert in the roof is 160 mm or and purlin overlap, and the mining plate paste butyl tape two above, with structural adhesive, and will gather together with choi steel plate in the bracket above, prevent the reverse flow of water. The personnel can be seated on the steel ladder, and the harness is mounted on the purline or the steel ladder. To install the pull rod, hold or grip the lever with pliers, and tighten the nuts with a wrench on the other end. Due to the long length of the metal roof panel, the installation process may slip, move up, or there will be some place in the metal roof panel bite. When the metal roofing plate is laid, the hole should be reserved, such as the mining plate and the slope gas building, so as to facilitate the correct installation of the lighting panel and the smooth slope gas building. RE: How to install metal roof panel? - askaluadmin - 03-22-2018 Tips for Installing Metal Roofing Make sure the first panel is installed square - all the other panels will follow it. On exposed fastener panels: While you don't have to predrill holes for your screws, predrilling panels will make it easier to get the screw lines straighter. - You can predrill a stack of about 10 panels at a time. - Make sure you measure for predrilling accurately. If you pop lines for your screws, make sure to use blue chalk, and NOT RED CHALK. Red chalk is very difficult to get off and can stay on for months, while blue chalk will usually wash off with the next rain. If you need to cut panels lengthwise, you can score them with a box cutter several times, and then bend it back and forth until it breaks off, producing a clean edge. You can also use tin snips or the TurboShear Drill Attachment for cutting them. Screw your fasteners in straight, and don't overtighten them. The best way to do this is to set your drill tension, preferably testing it out on a scrap piece of metal or on an area that will be covered over by a ridge cap or other flashing. Wear protective rubber coated gloves while working with metal roofing and flashings. This not only protects you from the sharp metal edges, it also gives you a better grip on the metal roofing. After you finish installing the metal roofing, make sure to brush off any metal filings / shavings that are on the roof. Otherwise they will cause unsightly rust spots where they rest on the metal roofing. RE: How to install metal roof panel? - aluhm - 03-22-2018 A steel roof is long-lasting and withstands inclement weather. It is also recyclable. You can order steel roofing from a metal roofing distributor. You can buy the tools needed to install a steel roof from a hardware or home improvement store. Use these tips to install a steel roof. Steps [/url] 1 Measure the roof. Use a tape measure to determine the distance between the ridge and eave of the roof. Add the amount of desired overhang to that measurement if you want the roofing to hang over the eaves. Determine the roof's width. Divide the roof's width by 3. The result gives you the number of panels that you need. For a roof that is 45 feet (13.7 m) wide, you will need 15 metal panels. Panels come in a width of 3 feet (.91 m) each, but are cut to desired lengths. 2 Order your steel roofing panels. Give the roof measurements to a metal roofing distributor when ordering your panels. 3 Cover the shingles. This is a good time to add a radiant barrier insulation for energy efficiency or you can cover the roof with 30-pound (13.6-kg) roofing felt to keep moisture away from the roof. Leave the old shingles on the roof. Use a staple gun or plastic cap nails to secure the insulation or roofing felt . 4 Lay the batten boards. Batten boards help to secure the steel panels to the roof. Lay 1-by-4-inch (2.5-by-10.2-cm) pine boards over all of the roofing felt. The boards should run parallel with the ridge and the eaves. Place the boards 24 inches (61 cm) apart from eave to ridge. Use a drill to screw the boards into the roof. 5 Install the eave flashing. Eave flashing helps water to flow off of the roof. Use a hammer and nails to attach eave flashing to the eaves. Install the eave flashing along the roof's entire width. If the roof has gutters, the eave flashing should cover over each of the gutter's sides. 6 Apply closure strips. Closure strips help close gaps beneath the steel roofing panels where animals and pests may hide. Place closure strips onto the eave flashing. Place a drop of butyl tape sealant over the closure strip. 7 Install the first steel roof panel. Place the first panel along 1 edge of the roof. The bottom end of the panel should hang 3/4 inch (1.9 cm) over the eave. Screw the panel onto each 1-by-4-inch (2.5-by-10.2-cm) board. 8 Install the remaining panels. Lay the second panel along the first panel. The high ridges that run the length of the second panel should overlap the ridges on the first panel. Secure the second panel by screwing it onto the first panel. Place the screws into the overlapping ridges. Insert a screw every foot (30.5 cm) from the eave to the ridge. Repeat the process with the rest of the panels. Cover the entire roof. 9 Install the gable trim. Gable trim gives the roof's edges a smooth appearance. Apply a thin line of butyl tape sealant along the side edge of the roof. Place the gable trim over the side edge of the roof. Screw the gable trim into the roof. Install gable trim on all edges of the roof. [url=https://www.wikihow.com/Install-a-Steel-Roof#/Image:Install-a-Steel-Roof-Step-10.jpg] 10 Install the ridge cap. The ridge cap helps water to flow off of the roof. Apply a thin line of butyl tape sealant along the roof's ridge. Place outside foam closures along the roof's ridge. Apply butyl tape sealant in a thin line along the length of the foam closures. Place the ridge cap over the roof. Secure the ridge cap on both sides of the peak with evenly spaced screws. more https://www.wikihow.com/Install-a-Steel-Roof